Search This Blog

Surfe.be - Banner advertising service

Huawei C8100 Windows Mobile Configuration

Huawei C8100

Calibrating the Touchscreen
When operating the phone with the stylus, if the phone does not respond to your operation correctly, you can calibrate the screen as follows-
1. Select Start> Settings> System> Screen> Align screen to display the screen for calibration.
2. Calibrate the screen by tapping the center of the cross on the screen accordingly to the displayed messages.
3. During the calibration, tap the center of the cross accurately, so that the phone responds to your tap and text entry on the screen correctly after the calibration.


Using the Motion Sensor
Your phone is equipped with a motion sensor. When the motion sensor is enable, the display on the screen reorients itself depending on the movement of the phone.
To set the motion sensor, you can select Start> settings> System> Gravity Sensor> Settings. The available options are, 
  • Enable auto rotate
  • Enable overturn mute ring
  • Enable overturn mute alarm
  • Enable rote full screen
  • Enable sake to switch



Signal Indications
The color and status of the back light of the navigation key, call key and End key informs you of the following:
  • Red (on): The phone is being charged
  • Green (on): The phone is fully charged
  • Green (blinking): There is a system message
  • Blue (blinking): Bluetooth is turned on.




Adding a New Contact
1. Select Start> Contacts to open the Contacts screen.
2. Tap New> Outlook Contact/UIM Contact, and enter the contact information.
3. Tap Ok to save.


Settings WLAN
WLAN provides a brand new mode for wireless network acess. to use WLAN for network access on the  phone, you need to access a wireless access point or a hot spot.

Select Start> Settings> Connections> WLAN and then the Search for networks. The system then automatically turns on WLAN and search for available WLAN networks. After the search, you can tap any of the access points to access the corresponding WLAN networks. You can access corresponding WLAN network directly if it is open for access. If the network is WEP-encrypted, you need to enter the corresponding WEP key to access the network.


Using the Task Manager
To open the task manager, select Start> Programs> Task Manager.
With the Task Manager, you can check the application that are currently running on the phone and close an application or switch to an application quickly. The running speed of the phone will be advesly affected if too many application are running.



Memory Status
To view the memory usage, select Start> Settings> System>  Memory.



Synchronization
With ActiveSync, you can synchronize your device with a PC and back up and restore your data.

Connecting to a PC
1. Install ActiveSync on a PC.
Note: On a PC with the Windows Vista or Windows 7 OS installed, you need to install Windows Mobile Device Center; on a PC with the Windows XP OS or TH OSs of erliar version installed, you need to install ActiveSync.

2. Connect your device to the PC.

3. Perform the connection to the PC according to the no-screen instruction.
Note: You can connect your device to the PC by using a USB cable or via Bluetooth. When the USB cable is used, your device can automatically synchronize with the PC. When Bluetooth is used, you need to first pair your device with the PC.



Synchronizing Information
You can take information from your computer wherever you go by synchronizing then to you device. The following types of information can be synchronized between your computer and your device:

Microsoft Office Outlook, which includes Office Outlook email, contacts, calendar, tasks, and notes.
Favourites, which are the bookmarked links to to your favourite Web sites.
Media, such as pictures, music, and video.
Files such as documents and other files.


Synchronizing Music and Video
You can set up Windows Media Player on your computer to synchronize music and video with your device.

Install Windows Media Player version 11 or later on your computer.
Connect your device to the computer with a USB cable.
Set up a sync partnership between your device and your computer's Windows Media Player.


Synchronizing with the Exchange Server
You can connect your device to the Internet and synchronize with the Exchange Server.
1. Select Start> Program> ActiveSync> Menu> Add Server Source.
2. Enter your email address and tab Next.
3. Enter a server address and tap Next.
4. Enter your Exchange Server's user name, password and domain name and tab Next.
5. Select the type of data you want to synchronize.
6. When you are done, tap Finish.




Connectivity 

Using Bluetooth
Bluetooth is a short-range wireless communications technology. Devices with Bluetooth capabilities can exchange information over a distance of about 10 meters. Wall or other obstacles between devices may block or impair the wireless connection.

Make Your Device Visible
To allow other devices to find and connect to your device, you have to activate the visibility mode.
1. Select Start> Settings> Connections> Bluetooth.
2. Tab the Mode tab.
3. Select the Turn on Bluetooth and Make this device visible to other devices check boxes and tap Ok to save.

Connecting a Bluetooth Headset
You can use a Bluetooth hands-fee headset for your device.
Your device also supports Advance Audio Distribution Profile (A2DP), which allows you to use a Bluetooth stereo headset for hands-free phone conversions and stereo music listening.

1. Make sure that both your device and the Bluetooth headset are turned on and within a close range, and that the headset is visible.
2. Select Start> Settings> Connections> Bluetooth.
3. Tab Add new device in Device tab.
4. Tab the name of the Bluetooth headset, then tap Next.
5. Enter the PIN code delivered with your headset.


Sending Data via Bluetooth
You can send files to another Bluetooth-enabled device via Bluetooth.
1. Make sure that the Bluetooth function is enabled.
2. Select Start> Programs> File Explorer.
3. Locate an item o file you want to send.
4. Tap and hold the file and tap Beam File in the pop up menu.
5. Select a device from the list and Tab to Send.



Internet Explorer Mobile

Visiting a Web Site
Enter the URL address bar and press the Ok key.

Using Other Functions
While browsing Web pages, tab Menu to open the menu of Internet Explorer Mobile. You can also tab and hold an empty area on a Web page to open a structure menu.
  • Tab Add to Favourites to add the current web page to Favourites.
  • Tab View to set the text size and the view mode.
  • Tab Tools to send links, view properties, or open the options menu.
  • Tab and hold a picture and tab Save Image As to save the picture.
  • To minimize from full screen, just hold the Confirm key for few second, and then you will get the option to minimize.



Internet Sharing
Internet Sharing connects your computer to the Internet by using your device's data connection.

1. On your device, select Start> Programs> Internet Sharing.
2. In the PC Connection list, select USB or Bluetooth.
3. In the Network Connection list, select the name of the connection that your device uses to connect to the Internet.
4. Connect your device to the computer using the USB cable or via Bluetooth.
5. Tab Connect.





AnyData ASP-210C Windows Mobile Configuration




Connect to Internet or Create Dialup in Phone

  1. On the Home Screen, Press, Start> All Programs
  2. Select Settings > Connections > Dial-up
  3. Click on Option New
  4. Edit the following items:
    1. Connects to: This should be left as The Internet
    2. Phone number: This should be left as #777
    3. User name: This should be left as waps
    4. Password: This should be left as waps
    5. Domain: Leave it blank
  5. Press Done
  6. Press Home button, and press Start > All Programs. Click on Internet Explorer and start using the Internet.


Using Internet Sharing (Zooming in PC/Laptop Via Phone)


With Internet Sharing, you can connect your PC to the Internet by using device’s data connection (AnyData CDMS network). You can connect via USB or Bluetooth.
  1. You first create and Dial up in phone and install Microsoft ActiveSync version 4.5 on the computer.
  2. On the Home screen, press Start> All Programs> Internet Sharing
  3. Select USB as the PC Connection.
  4. Plug in the USB cable between the device and the computer.
  5. Press Connect.
  6. To end the Internet connection, press Discount on the Internet Sharing screen.


SD Memory Card Location in Phone

  1. On the Home screen, press Start> All Programs> File Explorer
  2. Press Up
  3. Select Storage Card folder and press Ok

Set-up email

  1. To begin with setup email, please connect to the internet.
  2. On the Home screen, press Start > All Programs.
  3. Select Messaging > Setup E-Mail.
  4. Enter your E-mail Address and Password, and press Next.
  5. For commonly used internet email domains like Hotmail, Yahoo and Gmail, this screen will automatically fetch the settings. If found, press Next and proceed to step 9. Else select “Try to get e-mail settings automatically from the Internet” and press Next.
  6. If the next screen display that Auto Setup has found settings for your email domain, press Next and proceed to step 9. If it Could not find settings, press Next and continue to next step for manually set.
  7. Select Your e-mail provider as one of the Internet e-mail. If unsure please contact with email provider.
  8. If prompted, enter your e-mail server in Incoming mail server; select the account type (for faster sync, IMAP4 is recommended). However, to use this feature your email account type on your PC also needs to be IMAP4.
  9. Enter Your Name (recipient of your e-mails will see this name as sender) and Account Display Name (will be displayed in the list of messaging options) and press Next.
  10. If prompt, enter your User name and Password, and press Next.
  11. If prompt, enter outgoing e-mail server in Outgoing (SMTP) mail server and press Next.
  12. Select how often your phone automatically connects to the server to check for incoming E-mails. You may also select the download size of incoming email and attachments.
  13. Press Finish. You may add multiple email accounts.


To Keep Standby or Keypad Lock

  1. Press and hold the End key to avoid accidental key presses and to keep the phone in Standby mode.

Short key to keep Bluetooth Switch on or off

  1. Press key combination Fn + B

Installing Active Synchronize

We can Synchronize Data between our Phone and PC.

  • What kind of Data We can synchronize?
  1. Outlook email, contacts, calendar Appointments, tasks, media files.
  2. Copy files directly from your PC to Phone or Phone to PC.

  • What is Software Name?
1. ActiveSync. Install ActiveSync on your PC.

  • To synchronize with a PC via data cable
  1. plug the data cable into the USB port on a PC
  2. The connection is established and the Microsoft ActiveSync window displays. Just press the Sync in ActiveSync in computer.
  3. To stop synchronizing, press stop.

  • To synchronize with a PC via Bluetooth cable
  1. on the home screen, press Start> All Programs> ActiveSync
  2. Select Menu> Connect via Bluetooth. Be sure to turn on Bluetooth.
  3. Just press the Sync in ActiveSync in computer.
  4. To stop synchronizing, press stop.

  • To change PC Settings
  1. Disconnect phone from your PC
  2. On the Home screen, press Start> All Programs> ActiveSync
  3. Press the Menu> Options.
  4. On an Windows PC, press the Menu>


Bluetooth

  • Bluetooth Setup
  1. Select Start> All Programs> Settings> Connections> Bluetooth
  2. Select Add New device and Press Ok.
  3. Select the searched Bluetooth device and press Next.
  4. Input a Passcode (1 to 16 character) same as input in the searched device.

  • To turn Bluetooth on and off
  1. Select Start> All Programs> Settings> Connections> Bluetooth
  2. Press Menu
  3. Select Turn On Bluetooth or Turn Off Bluetooth and Press Ok.

  • To Accept a Bluetooth partnership
  1. Ensure that Bluetooth is tuned on and set to visible mode.
  2. When prompted to accept a Bluetooth partnership with other device, press Yes.
  3. Enter a Passcode (same passcode that is entered on the device requesting the partnership)
  4. Press Next and Done.

  • To delete a Bluetooth partnership
  1. Select Start> All Programs> Settings> Connections> Bluetooth> Menu
  2. Select Delete and Press Yes.



To receive beamed information

Your phone can automatically receive beamed information, but you must enable the phone to do so through the connections menu.
  1. On the Home screen, press Start> All Programs
  2. Select Settings> Connects> Beam
  3. Check Receive Incoming Beams
  4. Press Done.


Beam information with Bluetooth
You can send files and information to other devices using Bluetooth.
  1. From the program, select the item you want to send, such as a task in Tasks, a contact card in Contacts, or a picture in Pictures & Videos.
  2. Press Menu and follow the steps below.
    1. For Contacts, press Send Contact> Beam.
    2. For Tasks, Press Beam Task.
    3. For Picture & Videos, press Beam … or Beam picture…
  3. Select the device to which you want to send the item.
  4. Press Beam.


Quick Action
Press the power button shortly.
List of this Function:
  1. Power off
  2. Lock
  3. Task Manager
  4. Wireless Manager
  5. All Profile Lists


Hard Reset

After a hard reset, all personal data which are stored in the device will be lost and the device is restored to its original factory setting. Therefore, we should save the data in PC to reduce data lose due to a hard reset.
**Data will not lose from RIM card & SD card.

Tow ways to reset:
  • Power off state: Press and hold OK, Enter & power button simultaneously. You see the following message in the display “ CLEANING….ver1.7” on the device.
  • Power on state: Now Press and hold Reset, OK and Enter buttons simultaneously. Device will restart and after that remove from reset key. Continue to press and hold OK and Enter button for 3-4 seconds.

Sounds

To customize the Ring Tone:
Select Settings> Sound> Ring Tone

To customize the Other Sound:
Select Settings> Sound> Other Sound


Profile Settings


Start> All Programs> Settings> Profiles


To Customize the Home Screen

Start> All Programs> Settings> Home Screen

To Disable Phone Service or Bluetooth Service

We can disable both Phone Service and Bluetooth service.
Start> All Programs> Settings> Wireless Manager


Accessibility

Allow you to set the size of the text and characters, time outs, call alerts and volume on the phone.





Other Software

  1. Messenger
  2. Facebook
  3. Voice Command
  4. Live Search
  5. Task Manager
  6. Excel Mobile (File Need to be Copied from PC and Edit is possible, Creating a Excel file not possible)
  7. OneNote Mobile (File Need to be Copied from PC and Edit is possible, Creating a Not file not possible)
  8. PowerPoint (File Need to be Copied from PC and Edit is possible, Creating a Power Point file not possible)
  9. Word (File Need to be Copied from PC and Edit is possible, Creating a Word file not possible)
  10. Voice Recorder (Select Start> All Programs> Accessories> Audio Equalizer)
  11. Calculator (Select Start> All Programs> Accessories> Calculator)
  12. Stop Watch (Select Start> All Programs> Accessories> Stop Watch)
  13. Unit Converter (Select Start> All Programs> Accessories> Unit Converter)
  14. World Time (Select Start> All Programs> Accessories> World Time)


Modems’ Interface - User Graphics Interface (UGI)

ZTE AC2726 Modem's Interfaces

ZTE AC2726 - Internet Interface


ZTE AC2726 - Settings Interface



ZTE AC2726 - Voice Interface


ZTE AC2726 - SMS Interface





ZTE AC682 Modem Interfaces

ZTE AC682 - Internet Interface


ZTE AC682 - Settings Interface


ZTE AC682 - Voice Interface



ZTE AV682 - SMS Interface





Huawei EC169, EC122 and Huawei EC 167 Modem Interfaces


 Huawei Modem - Internet Interface


Huawei Modem - Voice Interface



Huawei Modem - SMS Interface

Installation of ZTE AC682 Modem in Ubuntu (Linux)

 



Operating System (OS) : Linux - Ubuntu, Mint



Step 1] Plug-in the ZTE AC682 modem and open Terminal to execute the following two commands to the whether ZTE AC682 modem is identified by operating system
ZoomUltra@Citycell:~$ lsusb
Bus 003 Device 002: ID 09da:000a A4 Tech Co., Ltd Port Mouse
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 003: ID 19d2:ffde ONDA Communication S.p.A.
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Here we get vendor id (19d2) and product id (ffde) of ZTE AC682 modem. However product id as ffde means that the modem acts as a storage device or a CD-ROM rather than as a modem.


Step 2] Now, we need to eject CD-ROM named as Zoom by right clicking on the icon. or execute the following command.

ZoomUltra@Citycell:~$ sudo eject





Note: USB mode switch software not necessary for this modem.






Step 3] Now execute lsusb command again to confirm whether product id changed from ffde to ffdd.
ZoomUltra@Citycell:~$ lsusb
Bus 003 Device 002: ID 09da:000a A4 Tech Co., Ltd Port Mouse
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hubBus 002 Device 004: ID 19d2:ffdd ONDA Communication S.p.A.
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Note: if product id not changed then unplug the ZTE AC682 device and re-plug it and execute the command again.


Step 4] Now give parameters to kernel for identification of the modem and to do this use the following command
ZoomUltra@Citycell:~$ sudo  modprobe   usbserial  vendor=0x19d2  product=0xffdd



Step 5] Execute wvdialconf command to modify the file, /etc/wvdial.conf on the basis of ZTE AC682 modem identified by kernel.
ZoomUltra@Citycell:~$ sudo wvdialconf
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
….........................
…..........................
ttyUSB0<*1>: ATQ0 V1 E1 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyUSB0<*1>: Modem Identifier: ATI -- Manufacturer: QUALCOMM INCORPORATED
ttyUSB0<*1>: Speed 9600: AT -- OK
ttyUSB0<*1>: Max speed is 9600; that should be safe.
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
…............................Found a modem on /dev/ttyUSB0.
Modem configuration written to /etc/wvdial.conf.
ttyUSB0: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"

Step 6] Before execute the final command we have to modify the /etc/wvdial.conf file to set phone number, user name and password based on ISP requirement
ZoomUltra@Citycell:~$ sudo gedit /etc/wvdial.conf
[Dialer citycell]
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
Phone = #777
ISDN = 0Username = waps
Init1 = ATZPassword = waps
Modem = /dev/ttyUSB0
Baud = 9600


Step End] Execute the wvdail command to get Citycell Ultra Zoom connection
ZoomUltra@Citycell:~$ sudo wvdial citycell
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATDT#777
--> Waiting for carrier.
ATDT#777
CONNECT
--> Carrier detected. Waiting for prompt.
~[7f]}#@!}!} } }=}!}$}%\}"}&} } } } }#}%B#}%}%}&hk#>}'}"}(}" !~
--> PPP negotiation detected.
--> Starting pppd at Fri Dec 3 23:01:31 2010
--> Pid of pppd: 1647
--> Using interface ppp0
--> pppd: ���[08]���[08]
--> pppd: ���[08]���[08]
--> pppd: ���[08]���[08]
--> pppd: ���[08]���[08]
--> pppd: ���[08]���[08]
--> local IP address 10.1.63.194
--> pppd: ���[08]���[08]
--> remote IP address 2.2.2.2
--> pppd: ���[08]���[08]
--> primary DNS address 117.18.224.146
--> pppd: ���[08]���[08]
--> secondary DNS address 117.18.224.147
--> pppd: ���[08]���[08]

To disconnect the Modem, just press Ctrl+C



Note: The following commands need to executive if security purpose unable to run the pppd called by wvdail in normal user mode rather than administration.
ZoomUltra@Citycell:~$ ls -l /usr/sbin/pppd
-rwsr-xr-- 1 root dip 273312 2010-03-07 09:59 /usr/sbin/pppd
ZoomUltra@Citycell:~$ sudo chmod o+x /usr/sbin/pppd
ZoomUltra@Citycell:~$ ls -l /usr/sbin/pppd
-rwsr-xr-x 1 root dip 273312 2010-03-07 09:59 /usr/sbin/pppd


Note: To check IP addresses and connection related other information then execute the following command
ZoomUltra@Citycell:~$ ifconfig
ppp0 Link encap:Point-to-Point Protocol
inet addr:10.1.105.59 P-t-P:2.2.2.2 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:4 errors:1 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:64 (64.0 B) TX bytes:97 (97.0 B)















Surfe.be - Banner advertising service